How to Make Decorative Scalloped Molding

Other things that you will need are a good table mounted router with a desired profile bit including a rub bearing, a jig saw or band saw, and sandpaper or a spindle sander and a wood rasp.

How to Make Decorative Scalloped Molding

How to Make Decorative Scalloped Molding

---

How to Make Decorative Scalloped Molding

How to Make Decorative Scalloped Molding

Start by drawing the shape of .5 of the piece of molding on the plywood or cardboard. This is to be .5 of the width of the cabinet that you are going to build plus enough past the end to make a miter if needed.

Next select a piece of lumber that is wide enough and long enough to make the molding. This needs to be twice as long as the pattern from step one. Using a Combination square and a pencil draw a line across the center of the board. Set the pattern on the line and trace around the pattern. Turn the pattern over and place it on the otherside if your center line. Now trace the other .5. This approach will help keep the molding symmetrical.

Next cut out the shape using a band saw or jig saw leaving the outside edge to be cut later. Sand the edge smooth and check that the contour doesn't have any unwanted humps.

Select a router bit that has a bearing and is appropriate for the style of furniture that you are building and install it in the table mounted router. Be sure to use a starter pin installed in the base of the router to safely start the cut. Now route the edge that will become the lower profile of the piece. Be sure not to run around the end of the piece.

Using a marking gauge or a pencil and your finger as a gauge, mark the outside of cut on the piece. Cut theoutside line with a band saw or jig saw. Sand the outside edge and make sure that the piece is smooth and does not have any unwanted humps in it.

Warnings:

Always wear safety glasses when using any power tools.

When using a table mounted router without a fence always use a Starter Pin to guide the work piece into the cutter.
Always keep a firm grip on your work piece and make sure your hands are cleat of the cutter.

How to Make Decorative Scalloped Molding

Woodworking Jigs-Why? How To Build?

Woodworking machines and hand tools need jigs and fixtures to reach their full potential. A table saw can slice up wood adequately but tenon making requires a fixture. Drilling holes in line on the drill press requires a fence. You can free hand Bandsaw circles. If you want two of them the same diaMeter, you'll need a jig.

Woodworking Jigs-Why? How To Build?

Woodworking Jigs-Why? How To Build?

---

Woodworking Jigs-Why? How To Build?

Woodworking Jigs-Why? How To Build?

Hand tools are just as dependent on jigs. A corner chisel needs a guide to chisel a mortise square corner. Most cutting tools need help to perform their chosen task. Routers are the worst case situation-they are simply dependent and reliant on support.

You might think that the key to getting control of the router are difficult. Instinctively, you would think a whirling tool enclosed in a metal case is not good for jigs andfixtures, but it is.

Commercial jigs are available, as some experts suggest. Can you make your own? If done properly, they are better than most commercial jigs and cost a whole lot less. You can improve the jig after building your first one. As this progression continues, your work improves. Often, you find more uses for the same jig.

The point is jigs help you become a quality woodworker. Moreover, your skills will increase as you make woodworking jigs!

A good woodworking jig allows quick set-ups, and efficient cuttings. With a superior jig, few mistakes are possible and not much skill is required for good results. Can you ask for more?

Some jigs take time to make. Once completed, you can use them repeatedly. This is an excellentreason to use first rate materials and take time to align the pieces.

Let's discuss a couple of the woodworking jigs that you can make. These jigs are superior to Commercial Jigs.

Mortise Jig

Why bother with a mortise jig? The mortise and tenon is the joint of choice in furniture. The joint resists tension and twist, and work great in compression and shear. In addition, registration of your joint is perfect.

Some people use hand chisels or a drill press with hollow square chisel. For the most precise and repeatable mortises, you should consider a mortise jig. For a perfect fit, you want the fit the tenon to mortise exactly.

The Mortise Jig gives excellent results without giving away anything. The mortise and tenon jointwill last for a lifetime. You can make mortises of nearly any length, width or depth. Moreover, they are repeatable for multiple cuts.

How does the mortise jig work?

The beauty of this system is simplicity.
The set up is quick. The cuttings are efficient. It supports the workpiece in all directions. It locks in the router to remove only the mortise. It is repeatable for several pieces, such as multiple drawers ' cavities on each side of a desk. It makes the joint the uniform and strong.
Tenon Jig

A Tenon Jig is easy to make. It provides precise four-faced tenons of nearly any length and width. It has fewer parts than the Mortise Jig, yet is just as accurate.

With a Tenon Jig, the cuttingresults are excellent, the process Fast, and guaranteed safety. All that you need is a little patience to make a Tenon Jig. Along with the Mortise Jig, you can instantly have a mortise and tenon joint that fits snugly and aligns correctly.

Using these two woodworking jigs, you can craft precise mortise and tenon joints in less time than any other method. You get exact alignMent for both parts. Can you ask for more?

You can build many woodworking jigs. Examples: Baby Crib Spindles Jig, Circle Cutting Jig, Edge Guides, Inlay Jig & Templates, Lapping Jig, Jig, Notching and Router Insert Plate Jig & templates, just to name a few.

You will gain confidence with making jigs. It gives you more versatilitywith your projects. With a little practice, you can't go wrong!

Have fun making Great Woodworking Jigs with safety in mind!

Woodworking Jigs-Why? How To Build?